STAINLESS INSERT 19MM TO SUIT 38MM PVC RIGID GUNWALE 3.65M LENGTH
Available to order for collect — supplier, typically 2–10 business days
Please Note: This is not a complete product. You must purchase the desired length of PVC Rub Rail to attach the insert to. Refer to related products below. The 19mm (3/4”) 316-grade stainless steel insert suits the Rigid PVC Rub Rail 38mm body for a classic look. The PVC Rub Rail 38mm is available in two different styles (white or black), with leg or without leg (see related products). Features: 1.5mm thick 316-grade stainless steel Pre-drilled 5mm mounting holes, usually found every 150mm Mounting hardware not included Sold in pre-cut lengths of 3.65m Fixing Method In order to achieve a good finish we recommend that 2 persons are used when fitting this profiles. Remove any existing profiles, end caps, insert, fixings and fendering. There will quite likely be silicone sealant behind the fendering which might pull away when the fendering is removed, otherwise use a putty knife to gently remove any excess or loose silicone sealant. New holes will probably be required for the new fendering so go around the boat filling in the holes left by the old fendering’s fixings sealant. Place Rigid PVC Body (sold separately) against the hull (if the profile has a lip then this should cover the underside of the deck moulding). Place the pre-drilled stainless steel insert into the channel. It may assist to hold the insert in place with masking tape which also can be used to protect insert when drilling, then drill directly into the hull and secure in place with screws. Tip: by applying some sealant to the end of each screw before fitting you will ensure that each hole is well sealed. Lengths should be butt joined to give the appearance of a continuous length. Trimming may be required of the body in order to finish the transom. We recommend using a hack saw to achieve this and an end cap should then be used to complete the finish. Secure and finish the fendering with an end cap (where available). Please note: In ambient conditions this Rigid PVC Body should be able to be fitted without prior heating, however, in some cases it may be necessary to apply heat directly to the area with a hot air gun. In these extreme cases be sure to apply the heat over an area and not just to a single spot. This will avoid any potential damage to the hull, paint, gelcoat or fendering.
$139.04
Not all goods are kept in store; some come direct from the supplier so it could take multiple business days to arrive in store.
Click & collect: goods from JPW, RWB and Taylor Marine are typically ready in 2–5 business days. Goods from Sam Allen (east coast) are typically ready in 5–10 business days.
Please Note: This is not a complete product. You must purchase the desired length of PVC Rub Rail to attach the insert to. Refer to related products below. The 19mm (3/4”) 316-grade stainless steel insert suits the Rigid PVC Rub Rail 38mm body for a classic look. The PVC Rub Rail 38mm is available in two different styles (white or black), with leg or without leg (see related products). Features: 1.5mm thick 316-grade stainless steel Pre-drilled 5mm mounting holes, usually found every 150mm Mounting hardware not included Sold in pre-cut lengths of 3.65m Fixing Method In order to achieve a good finish we recommend that 2 persons are used when fitting this profiles. Remove any existing profiles, end caps, insert, fixings and fendering. There will quite likely be silicone sealant behind the fendering which might pull away when the fendering is removed, otherwise use a putty knife to gently remove any excess or loose silicone sealant. New holes will probably be required for the new fendering so go around the boat filling in the holes left by the old fendering’s fixings sealant. Place Rigid PVC Body (sold separately) against the hull (if the profile has a lip then this should cover the underside of the deck moulding). Place the pre-drilled stainless steel insert into the channel. It may assist to hold the insert in place with masking tape which also can be used to protect insert when drilling, then drill directly into the hull and secure in place with screws. Tip: by applying some sealant to the end of each screw before fitting you will ensure that each hole is well sealed. Lengths should be butt joined to give the appearance of a continuous length. Trimming may be required of the body in order to finish the transom. We recommend using a hack saw to achieve this and an end cap should then be used to complete the finish. Secure and finish the fendering with an end cap (where available). Please note: In ambient conditions this Rigid PVC Body should be able to be fitted without prior heating, however, in some cases it may be necessary to apply heat directly to the area with a hot air gun. In these extreme cases be sure to apply the heat over an area and not just to a single spot. This will avoid any potential damage to the hull, paint, gelcoat or fendering.
- SKU: JPW9832
- Category: Fenders
- Vendor: JPW Marine
TRUSTED FISHING & BOATING BRANDS
Continuously scrolling list of 66 trusted brands.